Calculation tool
HV-MONITORING-RANGE-ACCURACY-CALC — TPS4141-Q1 Design Calculator
Spreadsheet calculator to help determine High Voltage measurement range and accuracy based on customer requirements.
TPS4141-Q1
Automotive 1200V configurable precision resistor divider with integrated switch
Data sheet
TPS4141-Q1
- Qualified for automotive applications
- AEC-Q100 grade 1: –40°C to 125°C ambient operating temperature
- Integrated high-voltage resistor divider
- 30MΩ total resistance, precision matched divider
- No exposed high-impedance nodes improves measurement integrity from board contaminants
- Integrated high-voltage disconnect switch
- 1200V standoff voltage, uni-directional blocking
- <1.5µA leakage at TA = 105°C
- High accuracy divider and precision buffer amplifier
- Buffered output for easy interfacing to analog-to-digital converters
- Dynamically selectable gain settings to maximize accuracy across high-voltage sensing range
- Typical gain error ± 0.15%
- Maximum input offset error ± 220mV
- Support for uni-directional and bi-directional voltage sensing up to ±1200V
- Dynamic switching between uni-directional and bi-directional voltage sensing operation
- Low supply current
- 5mA ON state current
- 5.5µA OFF state current
- SOIC (DWQ-11) package
- Creepage and clearance ≥8mm from high-voltage sensing pin to all other pins
The TPS4141-Q1 is a high-voltage, precision matched resistor divider with an integrated programmable-gain amplifier. The TPS4141-Q1 also integrates a high-voltage switch to allow for connecting or disconnecting the high-voltage sense pin. The device is designed for automotive and industrial applications where accurate, high-voltage measurements are required.
The TPS4141-Q1 programmable-gain amplifier supports four divider ratios using DIV0 and DIV1 inputs. DIV0 and DIV1 can be set to fixed divider ratios and may also be changed dynamically while in operation. This allows for matching the amplifier output (AOUT) to the full-scale input voltage of the analog-to-digital signal chain, improving accuracy over the entire voltage sensing range of interest.
The TPS4141-Q1 supports uni-directional or bi-directional voltage measurement. Bi-directional voltage measurement is supported by supplying an external precision voltage reference from REF to HVGND. Switching between bi-directional and uni-directional voltage sensing during operation is possible using DIV0 and DIV1. Connecting REF to HVGND provides uni-directional voltage sensing only.
The TPS4141-Q1 integrates a high-voltage switch with a standoff voltage greater than 1200V from the high-voltage sense pin (HV) to ground (HVGND). The switch provides uni-directional current blocking from HV to HVGND when disconnected.
Technical documentation
No results found. Please clear your search and try again.
View all 3 | Type | Title | Date | ||
|---|---|---|---|---|
| * | Data sheet | TPS4141-Q1 Automotive 1200V Configurable Precision Resistor Divider With Integrated Switch datasheet (Rev. A) | PDF | HTML | 30 May 2025 |
| Application note | Using Integrated Designs to Optimize High-Voltage Measurement | PDF | HTML | 04 Aug 2025 | |
| EVM User's guide | TPS4141-Q1 Evaluation Module User's Guide | PDF | HTML | 19 Nov 2024 |
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
TPS4141Q1EVM — TPS4141-Q1 evaluation module
The TPS4141-Q1 evaluation module (EVM) contains multiple test points and jumpers to fully evaluate the performance and functionality of the TPS4141-Q1 device. The evaluation module contains everything needed to test and assess the TPS4141-Q1 before designing into part of a greater application's (...)
Simulation tool
PSPICE-FOR-TI — PSpice® for TI design and simulation tool
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| SOIC (DWQ) | 11 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.