Inicio Lógica y traducción de voltaje Traductores de tensión y desplazadores de nivel Conversión de tensión
Inicio
Lógica y traducción de voltaje
Traductores de tensión y desplazadores de nivel
Conversión de tensión

SN74AVCH4T245-Q1

ACTIVO
Haga su pedido ahora
Hoja de datos

SN74AVCH4T245-Q1

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Bits (#) 4 Data rate (max) (Mbps) 380 Topology Push-Pull Vin (min) (V) 1.2 Vin (max) (V) 3.6 Vout (min) (V) 1.2 Vout (max) (V) 3.6 Applications GPIO, I2S, JTAG, PCM, SPI, UART Features Bus-hold, Partial power down (Ioff) Technology family AVC Supply current (max) (mA) 0.016 Rating Automotive Operating temperature range (°C) -40 to 125
Bits (#) 4 Data rate (max) (Mbps) 380 Topology Push-Pull Vin (min) (V) 1.2 Vin (max) (V) 3.6 Vout (min) (V) 1.2 Vout (max) (V) 3.6 Applications GPIO, I2S, JTAG, PCM, SPI, UART Features Bus-hold, Partial power down (Ioff) Technology family AVC Supply current (max) (mA) 0.016 Rating Automotive Operating temperature range (°C) -40 to 125
TSSOP (PW) 16 32 mm² (5 mm × 6.4 mm)
  • Control inputs VIH/VIL levels are referenced to VCCA voltage
  • Fully configurable dual-rail design allows each port to operate over the full 1.08V to 3.6V power-supply range
  • Ioff supports partial power-down-mode operation
  • Bus hold on data inputs eliminates the need for external pull-up/pull-down resistors
  • Supports data rate up to:
    • 500Mbps (1.08V to 3.6V translation)
  • Latch-up performance exceeds 100mA per JESD 78, class II
  • ESD protection exceeds JESD 22:
    • 8000V Human Body Model (A114-A)
    • 200V Machine Model (A115-A)
    • 1000V Charged-Device Model (C101)
  • Control inputs VIH/VIL levels are referenced to VCCA voltage
  • Fully configurable dual-rail design allows each port to operate over the full 1.08V to 3.6V power-supply range
  • Ioff supports partial power-down-mode operation
  • Bus hold on data inputs eliminates the need for external pull-up/pull-down resistors
  • Supports data rate up to:
    • 500Mbps (1.08V to 3.6V translation)
  • Latch-up performance exceeds 100mA per JESD 78, class II
  • ESD protection exceeds JESD 22:
    • 8000V Human Body Model (A114-A)
    • 200V Machine Model (A115-A)
    • 1000V Charged-Device Model (C101)

This 4-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.08V to 3.6V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.08V to 3.6V. The SN74AVCH4T245-Q1 is optimized to operate with VCCA/VCCB set at 1.08V to 3.6V. It is operational with VCCA/VCCB as low as 1.08V. This allows for universal low voltage bidirectional translation between any of the 1.2V, 1.5V, 1.8V, 2.5V, and 3.3V voltage nodes.

The SN74AVCH4T245-Q1 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input and the output-enable (OE) input activate either the B-port outputs or the A-port outputs or place both output ports into the high-impedance mode. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports is always active and must have a logic HIGH or LOW level applied to prevent excess ICC and ICCZ.

The SN74AVCH4T245-Q1 device control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by VCCA.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

The VCC isolation feature is designed so that if either VCC input is at GND, then both ports are in the high-impedance state. The bus-hold circuitry on the powered-up side always stays active.

Active bus-hold circuitry holds unused or undriven data inputs at a valid logic state. Use of pull-up or pull-down resistors with the bus-hold circuitry is not recommended. The bus-hold circuitry on the powered-up side always stays active.

To put the device in the high-impedance state during power up or power down, tie the OE pin to VCC through a pull-up resistor; the current-sinking capability of the driver determines the minimum value of the resistor.

This 4-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.08V to 3.6V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.08V to 3.6V. The SN74AVCH4T245-Q1 is optimized to operate with VCCA/VCCB set at 1.08V to 3.6V. It is operational with VCCA/VCCB as low as 1.08V. This allows for universal low voltage bidirectional translation between any of the 1.2V, 1.5V, 1.8V, 2.5V, and 3.3V voltage nodes.

The SN74AVCH4T245-Q1 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input and the output-enable (OE) input activate either the B-port outputs or the A-port outputs or place both output ports into the high-impedance mode. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports is always active and must have a logic HIGH or LOW level applied to prevent excess ICC and ICCZ.

The SN74AVCH4T245-Q1 device control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by VCCA.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

The VCC isolation feature is designed so that if either VCC input is at GND, then both ports are in the high-impedance state. The bus-hold circuitry on the powered-up side always stays active.

Active bus-hold circuitry holds unused or undriven data inputs at a valid logic state. Use of pull-up or pull-down resistors with the bus-hold circuitry is not recommended. The bus-hold circuitry on the powered-up side always stays active.

To put the device in the high-impedance state during power up or power down, tie the OE pin to VCC through a pull-up resistor; the current-sinking capability of the driver determines the minimum value of the resistor.
filter Buscar otro/a Conversión de tensión
Descargar Ver vídeo con transcripción Video

Documentación técnica

No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 4
Documentación principal Tipo Título Opciones de formato Descargar la versión más reciente en inglés Fecha
* Hoja de datos SN74AVCH4T245-Q1 Automotive 4-Bit Dual-Supply Bus Transceiver With Configurable Level-Shifting, Voltage Translation, and 3-State Outputs datasheet PDF | HTML 15/02/2024
Nota sobre la aplicación Schematic Checklist - A Guide to Designing With Fixed or Direction Control Translators PDF | HTML 2/10/2024
Nota sobre la aplicación Schematic Checklist - A Guide to Designing with Auto-Bidirectional Translators PDF | HTML 12/07/2024
Nota sobre la aplicación Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) PDF | HTML 3/07/2024

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

14-24-LOGIC-EVM — Módulo de evaluación genérico de productos lógicos para encapsulados D, DB, DGV, DW, DYY, NS y PW de

El módulo de evaluación (EVM) 14-24-LOGIC-EVM está diseñado para admitir cualquier dispositivo lógico que se encuentre en un encapsulado D, DW, DB, NS, PW, DYY o DGV de 14 a 24 pines.

Guía del usuario: PDF | HTML
Productos y hardware compatibles
En inventario
Límite:
??asset.out-of-stock-ti_es_MX??
No disponible
Placa de evaluación

14-24-NL-LOGIC-EVM — Módulo de evaluación genérico de productos lógicos para encapsulados sin plomo de 14 a 24 pines

El 14-24-NL-LOGIC-EVM es un módulo de evaluación flexible (EVM) diseñado para admitir cualquier dispositivo lógico o de traducción que tenga un encapsulado BQA, BQB, RGY, RSV, RJW o RHL de 14 a 24 pines.

Guía del usuario: PDF | HTML
Productos y hardware compatibles
En inventario
Límite:
??asset.out-of-stock-ti_es_MX??
No disponible
Placa de evaluación

AVCLVCDIRCNTRL-EVM — EVM genérico para dispositivo de traducción bidireccional controlado por dirección compatible con AV

El módulo de evaluación genérico está diseñado para admitir dispositivos de conversión controlados por dirección de semiconductor de óxido metálico complementario de baja tensión y AVC de uno, dos, cuatro y ocho canales. También es compatible con la retención de bus y los dispositivos de automoción (...)

Guía del usuario: PDF
Productos y hardware compatibles
En inventario
Límite:
??asset.out-of-stock-ti_es_MX??
No disponible
Encapsulado Pines Símbolos CAD, huellas y modelos 3D
TSSOP (PW) 16 Ultra Librarian
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene alguna pregunta sobre calidad, encapsulados o pedido de productos de TI, consulte el servicio de asistencia de TI. ​​​​​​​​​​​​​​

Videos