SLVSHK6 March   2025 TPS61381-Q1

PRODUCTION DATA  

1.   1
2. 1 Features
3. 2 Applications
4. 3 Description
5. 4 Pin Configuration and Functions
6. 5 Specifications
   1. 5.1 Absolute Maximum Ratings
   2. 5.2 ESD Ratings
   3. 5.3 Recommended Operating Conditions
   4. 5.4 Thermal Information
   5. 5.5 Electrical Characteristics
   6. 5.6 I2C Timing Characteristics
   7. 5.7 Typical Characteristics
7. 6 Detailed Description
   1. 6.1 Overview
   2. 6.2 Functional Block Diagram
   3. 6.3 Feature Description
      1. 6.3.1 VCC Power Supply and UVLO Logic
      2. 6.3.2 Enable or Shutdown
      3. 6.3.3 Device Operating Modes and Control Logic
      4. 6.3.4 Configured as Status Indicatior
      5. 6.3.5 Thermal Shutdown
   4. 6.4 Charger Feature Description
      1. 6.4.1 Charger Enable
      2. 6.4.2 LDO Charger
      3. 6.4.3 NiMH Battery Charging Profile
      4. 6.4.4 Lithium Battery Charging Profile
      5. 6.4.5 Super Capacitor Charging Profile
      6. 6.4.6 Battery Cold, Hot Temperature (TS Pin)
      7. 6.4.7 Charger Protection and Fault Condition Indication
   5. 6.5 Boost Feature Description
      1. 6.5.1 Enable and Start up
         1. 6.5.1.1 Automatic Transition into Boost Mode
         2. 6.5.1.2 Manual Transition into Boost Mode
      2. 6.5.2 Down Mode
      3. 6.5.3 Output Short- to-Ground Protection
      4. 6.5.4 Boost Control Loop
      5. 6.5.5 Current Limit Operation
      6. 6.5.6 Functional Modes at Light Load
         1. 6.5.6.1 Auto PFM Mode
         2. 6.5.6.2 Forced PWM Mode
      7. 6.5.7 Duty Cycle Limitation
      8. 6.5.8 BUB Voltage Loop
      9. 6.5.9 Spread Spectrum
   6. 6.6 Battery State-of-Health (SOH) Detection Feature Description
      1. 6.6.1 SOH Mode Operation
      2. 6.6.2 Multi-Signal Output in AVI Pin
      3. 6.6.3 Calculate Impedance of BUB
   7. 6.7 I2C Serial Interface
      1. 6.7.1 Data Validity
      2. 6.7.2 START and STOP Conditions
      3. 6.7.3 Byte Format
      4. 6.7.4 Acknowledge (ACK) and Not Acknowledge (NACK)
      5. 6.7.5 Slave Address and Data Direction Bit
      6. 6.7.6 Single Read and Write
      7. 6.7.7 Multi-Read and Multi-Write
8. 7 Register Maps
   1. 7.1  Register 00H: CHIP_ID
   2. 7.2  Register 01H: BOOST_SET1
   3. 7.3  Register 02H: BOOST_SET2
   4. 7.4  Register 03H: BOOST_SET3
   5. 7.5  Register 04H: CHGR_SET1
   6. 7.6  Register 05H: CHGR_SET2
   7. 7.7  Register 06H: CHGR_SET3
   8. 7.8  Register 07H: CHGR_SET4
   9. 7.9  Register 08H: CHGR_STATUS
   10. 7.10 Register 09H: SOH_SET1
   11. 7.11 Register 0AH: SOH_SET2
   12. 7.12 Register 0BH: CONTROL_STATUS
   13. 7.13 Register 0CH: FAULT_CONDITION
   14. 7.14 Register 0DH: STATUS_PIN_SET
   15. 7.15 Register 0EH: SW_RST
9. 8 Application and Implementation
   1. 8.1 Application Information
   2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
         1. 8.2.2.1 Selecting the External MOSFET
         2. 8.2.2.2 Inductor Selection
         3. 8.2.2.3 Capacitor in Back-Up Battery Side
         4. 8.2.2.4 Selecting the Output Capacitor
         5. 8.2.2.5 Loop Stability and Compensation Design
            1. 8.2.2.5.1 Small Signal Analysis
            2. 8.2.2.5.2 Loop Compensation Design
      3. 8.2.3 Application Curves
   3. 8.3 Power Supply Recommendations
   4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
10. 9 Device and Documentation Support
    1. 9.1 Device Support
       1. 9.1.1 Third-Party Products Disclaimer
    2. 9.2 Documentation Support
       1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
11. 10Revision History
12. 11Mechanical, Packaging, and Orderable Information

TPS61381-Q1 Automotive 400kHz, 40V, 15A Boost Converter
with LDO Charger and Battery State of Health Detection